Geekworm X1000 PCIe M.2 Key-M NVMe SSD PIP PCIe Peripheral Board for Raspberry Pi 5

Price: $15.50 - $14.29
(as of May 06, 2024 05:08:58 UTC – Details)

Product Description

Troubleshooting Steps

Check the hardware connection, make sure the FFC cable is fully inserted with right direction. (Change FFC cable to test if you have one.)Update EEPROM firmware: Check and upgrade the bootloader firmware to the latest version;Refer to Geekworm X1000 WiKi to check the SSD incompatibility List, change SSD to test.Enable PCIe: Must make sure to enable PCIe in the OS on the NVME SSD you are booting, instead of the OS on SD card. Too many people just enable PCIe in the OS on the SD CARD.Set NVME boot order;DON’T enable PCIe 3.0, ONLY PCIe 2.0 is supported by Raspberry Pi fundation.If your SSD is old and has a DOS partition, delete the DOS partition and repartition the SSD (feedback from buyer)Refer to the guide on Geekworm Wiki for more specific operations!!!(wiki.geekworm.com/NVMe_SSD_boot_with_the_Raspberry_Pi_5)

Note: The Raspberry Pi 5, M.2 NVME SSD, power supply is not included in the packing list.

Overview

The X1000 shield is an NVMe M2 2242 SSD PIP (PCIe Peripheral Board) for the Raspberry Pi 5 that uses the new PCIE interface of the Raspberry Pi 5 to utilise the NVME M2 SSDs for fast data transfers and ultra-fast booting.

Features

Model: X1000Compatible with other HAT shield;FFC cable is only 30mm length.Supports 2230/2242 NVMe M2 SSD only.(The X1000 hardware has no limit on NVME SSD capacity, which is dependent on the Raspberry Pi OS)Supports installation of official active coolersReserved space for POE module installationWith 40pin header, it can automatically supply power from GPIO, avoiding the problem of insufficient power supply for ultra-large capacity SSDs.

How to Power

Can power the X1000 shield directly from the FFC PCIe ribbon (providing maximum 5W of continuous power)

Packing List

1 x X1000 PCIe Peripheral Board1 x PCIe FFC Cable(30mm length)3 x M2.5×14.5mm F/F Spacers6 x M2.5x5mm Screws1 x M2x4mm Screws (to fix MVME M2 SSD)

Add to Cart

Add to Cart

Add to Cart

Add to Cart

Add to Cart

Customer Reviews

4.0 out of 5 stars
23

4.4 out of 5 stars
138

3.5 out of 5 stars
63

3.5 out of 5 stars
36

—

Price

$14.29$14.29 $14.90$14.90 $16.90$16.90 $15.00$15.00 $14.00$14.00

Compatible with
Raspberry Pi 5 Raspberry Pi 5 Raspberry Pi 5 Raspberry Pi 5&Official Active Cooler Raspberry Pi 5

Mounting Position
Top Top Bottom Top Top

M.2 NVMe SSD
2230/2242 2230/2242/2260/2280 2230/2242/2260/2280 2230/2242 2230/2242/2260/2280

Matching Case
P579(ASIN:B0CRD7XQCK) P579(ASIN:B0CRD7XQCK) P580(ASIN:B0CTGXVLL6) P579(ASIN:B0CRD7XQCK) or Official Raspberry Pi 5 ABS Case P579(ASIN:B0CRD7XQCK)

【Updated Version】Update from V1.3 to V1.5 version with one ACT LED Indicator; (On: Power OK/Standby, Flashing: Reading/Writing)
【Compatibility】Raspberry Pi 5 PCIe Peripheral Board only compatible with Raspberry Pi 5 8GB/ 4GB / 2GB/1GB SBC, Model: X1000
【M2 Key-M NVMe SSD Supported】Support M.2 KEY-M NVMe SSD 2230/2242 length installation.(Note: Do not reserve the nut column to fix the 2230 SSD, users need to find proper way to fix the 2230 SSD.)
【How to Power】Can Power the X1000 shield directly from the FFC PCIe ribbon (providing maximum 5W of continuous power). Recommend to use Geekworm PD 27W power adapter (ASIN:B0CP7WPZZY )
[SSD Capacity& Compatibility Note]The X1000 hardware has no limit on NVME SSD capacity, which is depend on the Raspberry Pi OS. Do not recommend to use NVMe SSD drives which is equipped with a Phison controller due to their proven incompatibility, refer to Geekworn WiKi for more details!
【Packing List】1 x X1000 PCIe Peripheral Board, 1x Screws Pack Accessories (Note: not include Raspberry Pi 5, SSD, TF card or power adapter.)